8. Emergency battery box jack
DC adapter(6V)
9. Knob
Streamline design and attractive appearance.
10. Idler wheel
Adopt special material, easy to roll and teardown.
OPERATION PROCEDURES
1.Uncover the emergency lock cover, fully insert the emergency key into the key hole, then turn the emergency key counter clockwise (90°) to open the lock;
Turn right the emergency key, then also turn right the knob to open the door. (Some models without knob, Turn right the emergency key to open the door)
2.Uncover the battery compartment cover on the back of the door. Install four AA batteries. Pay close attention to the polarity of the batteries. When the batteries are installed, the display will flash “□” and the system is actuated to scan the circuit, then show “good” after two times. And then the LCD display will wink out, into standby mode, please take off the emergency key and put on the emergency lock cover.
3. Once that is complete it will be in standby mode, while displaying date, time, week and voltage state.
SET CODE
1. Set user code:
When the door is on opening, the display will read “……”, now enter a 1-7 digit code (Enter factory preset code 1234 or your own code if the factory code has been changed) within 10 seconds and confirm it by pressing the “#” key. Now the display will read “IN”. You have now successfully set the user code which can be used to open the door.
(Note: If the setting user code time shall not exceed 10 seconds, otherwise the LCD screen will turn off automatically and the current operation will become invalid, you need to restart. When the code number reach to 8 digit, it will assigned anterior 8 digit as your new set user code automatically).
Example:
Press # then display ------- enter 1234 then press # to confirm，if the display reads “IN”.，the code confirmation is successful.
2. Set management code:
When the door is on opening, press #”, then press “00”, and then press the “ESC” on the back of the door.( do it in standby mode)
Example:
Press # then press 00 and then press ESC enter 123456 then press # to confirm，if the display reads “IN”.，the code confirmation is successful.
3. Change the code
Do it same as the above clause1 、2.
SET THE CALENDAR
1.In standby mode, press “*” key, enter into the date, week and time setting mode.
2.Use the digit key to set the year, month, day, week, hour and minute.
The parameter availableIn is as below:
Year: 00—99
Month: 01—12
Day: 01—31
Week: 1—7
Hour: 00—23
Minute: 00—59
3.When the you enter incorrect digit, press“*”key, the digit on the display will decrease by one, then you can set the correct digit.
OPEN / CLOSE
Open the door
1. Insert the key into the key hole,
2. Press the “#” key, the display will read “-----”
3. Enter the new code and press “ #” to confirm
4. Turn the key clockwise, then turn right the knob to open the door.
Close the door
1.Turn left the knob to lock up.
2.Turn left the key to lock up, then take off the key.
3.Some models without knob, just turn left the key to lock up, then take off the key.
ALARM FUNCTION
Alarm
1.Wrong code alarm:
If the wrong code is entered 3 times consecutively, the display will read ”Error”, and raise a sharp alarm. To cancel the alarm mode and to stop the alarm from sounding, just enter the correct code and will display “open”.
2.Being vibrated alarm:
In standby mode, press “0” key, the display will read“ALERT ON” and in alarm state. Once it being vibrated, inclined or hit, it will raise a sharp alarm. To cancel the alarm mode and to stop the alarm from sounding, just enter the correct code and will display “open”.
HIDE CODE FUNCTION
In order to keep its safety, it just display “□”, not the code digits when using.
The operating procedures is as below:
1.Press “#” key to start the power, then press “*” key, enter correct code, the display will read“□”, if the code is correct, it will display “open”.
2.When it opened, it will display the digit code then.
REPLACE THE BATTERIES / OPEN IN EMERGENCY
Replace the batteries
The power supply for the safe is DC adapter (6V) or Install four LR6 (AM3, AA) / 1.5V batteries. (use alkaline batteries).
When the LCD screen displays “LO-BATT”, it means the batteries are low, need to replace the batteries.
Open in emergency
1.If battery power located inside the safe has been used up, install the new ones properly into emergency battery box, plug emergency battery box into power outlet, then open the door as usual.
2. If there is something wrong with the safe or you forget your code, you can open the door by emergency key.
CAUTION
1.Do not put the operating instructions, the lock key and emergency key in the safe, and keep your lock key and emergency key in a secure location.
2. Remember your code by heart.
3. Under the circumstance that you won't be using this product for a long term, it is recommended that you should remove the batteries and reinstall them whenever you want to use it again. Your user code won't be lost.
WARRANTY
This product carries a one (1) year warranty against defects in workmanship and materials. This product is not guaranteed agains wear, breakage or misuse. If the unit should fail to operate correctly within one year from the date of purchase, call customer service at
SHENZHEN: (86)-755-89950089 DONGGUAN(86)-76922223345
GUANGZHOU: (86)-20-37278723 SHANGHAI: (86)-21-26885388
before returning unit to the store. Save packaging until you are satisfied with your purchase. We will, at our discretion either repair or replace the unit. This warranty is void if in the opinion of Quality Craft the unit has been tampered with, altered, misused, damaged or abused.
